Available Packaging and Coverage
4.2 kg from 90 g/m² per coat
14 kg from 90 g/m² per coat
Description and Properties
“DEOS 7” TM “Bayris” silk matt interior latex paint is designed for decorative and protective painting of walls and ceilings indoors on cement, cement-lime, brick, gypsum, plasterboard, wooden and wood-based surfaces, as well as wallpaper intended for painting. It provides a uniform silk matt finish and is ideal for areas requiring localised cleaning. “DEOS 7” TM “Bayris” offers excellent hiding power, creates a vapour-permeable coating, is resistant to washing (Class 1 resistance), applies easily without splashing and leaves no streaks on the surface.
According to research conducted by the Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine (Test Report dated 23.02.2023), the paint demonstrates antistatic properties.
Environmental benefits are confirmed in accordance with DSTU ISO 14024 requirements.
Surface Preparation
The surface intended for painting must be solid, dry, free from dust and grease contamination, and properly cured. Fresh cement-lime plaster may be painted after 3–4 weeks from application, gypsum plaster after 2 weeks. Old glue-based or lime paint coatings with poor adhesion should be removed. Surfaces previously painted with well-adhered emulsion paints should be washed with water and detergent, rinsed with clean water and dried. Uneven areas and cracks should be repaired with “Master Putz” TM Bayris. Areas affected by fungi should be treated with “Bio Stop” TM Bayris according to the instructions. Highly absorbent or fragile substrates should be primed with “Profi Grunt” TM Bayris according to the instructions. Non-woven and fibreglass wallpapers should be painted following the wallpaper manufacturer’s recommendations.
Application
Before application, “DEOS 7” TM “Bayris” paint should be thoroughly stirred until homogeneous.
A sufficient amount of paint should be prepared for painting one continuous surface area. When tinting paints from different production batches or packaging sizes, the products should be mixed together. The paint should be applied by roller, brush or spray in 2 coats with an interval of 2–4 hours. Do not add lime or mix with other types of emulsion paint. Painting work should be carried out at substrate and ambient temperatures above +10°C. The coating reaches full wash resistance 28 days after completion of painting works. Tools should be cleaned with water. During and after painting, the room should be ventilated until all odours have disappeared.
Important! Care of painted surfaces — under normal conditions, the coating achieves its full performance properties 28 days after application. Intensive cleaning of painted surfaces should therefore be avoided until this period has elapsed. Painted surfaces may be cleaned with water or warm soapy solution using a soft sponge or cloth. Avoid using hard-bristle brushes, as excessive friction during cleaning may cause glossy patches to appear on the painted surface.
Manufacturer’s warranty — the manufacturer guarantees that the paint meets the declared technical characteristics. Any modifications to the finished product composition, misuse of the product and/or use not in accordance with the manufacturer’s instructions may significantly alter its quality characteristics. Suitability of the product for specific materials and/or compatibility with other materials must be determined by the consumer through trial application. The manufacturer is not responsible for direct or indirect damages caused by the use of the product, as all conditions of use cannot be controlled.
Tinting
“DEOS 7” TM “Bayris” white paint is ready to use. The paint can be tinted using Bayris Color System tinting equipment or manually with colourants. Slight colour deviation from the reference shade may occur after drying.
Tinted paint cannot be returned or exchanged!
Technical Information
Classification according to DSTU EN 13300:
- gloss level: silk matt;
- wet scrub resistance: Class 1;
- hiding power: Class 1 at a coverage rate of 6 m²/l.
Maximum VOC content according to the Ukrainian Technical Regulation on VOC emission limits: (subcategory A/1/WB): 75 g/l. Ready-to-use product contains max. 15 g/l.
Waste disposal must be carried out in accordance with national and international legislation. Containers and liquid material residues must be taken to specialised hazardous waste collection points.
